Two rear light bars, same housing, same fitment, same installation method, same signal behavior. This is not a comparison in the usual sense, because there is almost nothing to compare. What separates them is a single line on the spec sheet — the light pattern — and once you have seen both described, the choice is a matter of taste rather than specification.
That is worth writing down precisely, because a buyer looking at two near-identical listings has no way to tell whether they are missing something. They are not. But there is one thing about both that is easy to miss and much more consequential than the pattern, and it is the first thing to check.
1. First: Which Model Y You Own
Before the pattern, the fitment — and this is where the two products stop being interchangeable with the rest of the range. Both bars are listed for Model Y 2020–2024. Both pages state, in the same words, that Model Y Juniper 2025 and later is not supported.
That matters more than it looks, because an exterior light bar is the kind of product that reads as universal. There is nothing in a photograph of a rear light bar that suggests a model-year boundary — it is a strip of LEDs in a housing, and it either suits the back of the car or it does not. A 2025 owner ordering on appearance has no cue that the answer is no.
For 2020–2024 owners the picture is simple: both fit, both install the same way, and the decision comes down to what you want the bar to look like when it lights.
2. What the Bar Actually Does
Both products solve the same problem, and the product pages describe it identically: a Model Y's tail lights are compact, and in dense traffic — at night or in the rain — a brake input is easy to miss. The bar adds a second, wider band of light across the rear so that a brake input is easier to notice.
The behavior is driven by the car's own signals rather than a switch or an app. Turn signals and hazards run amber. Brakes and headlights-on run red. The rest of the time the bar is dark. An onboard MCU chip keeps it in step with what the car is already sending, so there is nothing to turn on and nothing to configure.
That "dark the rest of the time" detail is worth pausing on. It means the bar is not a running light and not a decoration you leave on — it appears when you brake or indicate, and is otherwise invisible. If you were expecting a permanently lit accent across the rear, this is not that product.
3. The Only Difference
Here is the whole of it, described the way each page describes it.
| Zebra style | Heartbeat style | |
|---|---|---|
| Light pattern | Alternating lit and dark LED segments | A pulse that travels along the bar |
| What you see when it fires | A band of separated segments — striped | A running sequence — a pulse moving across |
| Everything else | Identical | |
That is the entire decision. The zebra reads as a set of distinct blocks lighting together; the heartbeat reads as movement, a pulse travelling from one end of the bar to the other. One is static in the sense that all segments are lit at once in a pattern; the other is sequential in the sense that the lighting travels.
4. Everything Else Is Identical
The two specification blocks match line for line. Same position, same housing material, same light source description, same controller, same water protection, same installation method, same package dimensions and weight. Reading them side by side is a slightly odd experience, because the only row that changes is the one about the pattern.
| Specification | Both products |
|---|---|
| Position | Rear |
| Housing material | ABS + PC |
| Light source | High-output LED beads |
| Control | MCU chip |
| Water protection | Sealed housing, weather resistant |
| Installation | Plugs into factory connector, no wire cutting, non-destructive |
| Professional fitting | Recommended on both pages |
| Package dimensions | 43 × 9 × 5 cm (16.9 × 3.5 × 2 in) |
| Package weight | 1.15 kg (2.5 lb) |
| Fitment | Model Y 2020–2024 · Juniper 2025+ not supported |
The installation sentence deserves a note, because it contains a small contradiction that is not really a contradiction. The bar plugs into the factory connector with no cutting or splicing — which sounds like a job you could do in a driveway. Both pages still recommend professional installation. That combination usually means the electrical part is trivial and the access is not: getting to the rear lighting harness on a Model Y is the work, not the connection.
5. The Part Nobody Reads
Both product pages carry the same line at the end of their notes, and it is the most substantive thing on either page after the fitment limit: rules about additional rear lighting vary by state and country, and you should check your local requirements before installing.
This is not boilerplate to skip past. A bar that adds red light to the rear of a vehicle, and amber for indication, sits in a category that many jurisdictions regulate — and the rules about what is permitted, where it may be mounted, and what colors may be shown are not consistent. The manufacturer is telling you, correctly, that they cannot answer that question for your jurisdiction.
6. Fitting and Testing
The post-installation test is specified on both pages and covers every mode the bar can show. It is worth doing in this order because it confirms each signal path separately.
- Left turn signal. Confirms the amber path on one side.
- Right turn signal. Confirms the other side independently — a bar that works on one side and not the other points at the connector, not the bar.
- Hazard flashers. Both sides amber at once.
- Brake lights. The red path, which is the function the product exists for.
- Headlights on. The pages state the bar runs red with headlights on as well as with brakes, so this is a separate test rather than a repeat of the brake check.
Both pages also give one maintenance note that is easy to ignore and does affect performance: keep the lens clean. Road film, salt and mud reduce how much light the bar throws — and since the point of the product is being noticed in traffic, a dirty lens quietly undoes the purchase.
GRUNDIG Zebra-Style LED Rear Light Bar
- Alternating lit and dark LED segments across the rear
- Amber with turn signals and hazards, red with brakes and headlights
- Plugs into the factory connector — no cutting, no splicing
- ABS + PC sealed housing, weather resistant
- Model Y 2020–2024 · Juniper 2025+ not supported
GRUNDIG Heartbeat-Style LED Rear Light Bar
- A pulse that runs along the bar rather than lighting all at once
- Amber with turn signals and hazards, red with brakes and headlights
- Same plug-in installation, same housing, same dimensions
- MCU controlled, follows the car's own signals automatically
- Model Y 2020–2024 · Juniper 2025+ not supported
If you are mapping out the rest of the car's lighting rather than just the rear, our guide to the four places a Tesla goes dark covers the frunk, the trunk, the dashboard and the ground beside the door — including which of those stop working on the newer cars. The pattern repeats: the fitment boundary is almost never where you would expect it.
7. Frequently Asked Questions
What is the actual difference between the zebra and heartbeat bars?
The light pattern, and nothing else. The zebra uses alternating lit and dark LED segments so the bar reads as a striped band. The heartbeat uses a pulse that travels along the bar, so the lighting appears to move. Housing, light source, control, water protection, installation, dimensions and fitment are identical on both.
Will either fit a 2025 Model Y Juniper?
No. Both products are listed for Model Y 2020–2024, and both pages state that Juniper 2025 and later is not supported. This is worth checking first because an exterior light bar looks universal in photographs — there is nothing about its appearance that signals a model-year limit.
Is one of them brighter?
Neither page states a brightness figure, lumen output or LED count, so there is no basis for claiming one is brighter. Both are described as high-output LED beads throwing a wider band of red than the factory brake lamps alone. If brightness matters to you specifically, ask the seller.
Does the bar stay lit all the time?
No. It runs amber with turn signals and hazards, red with brakes and with headlights on, and is dark the rest of the time. It follows the car's own signals automatically — there is no switch and no app, so there is nothing to turn on or configure.
Can I install it myself?
Both pages recommend professional installation even though the bar plugs into the factory connector with no cutting or splicing. That combination usually means the electrical connection is simple and the access is the work. Budget it as a job rather than a quick clip-on.
Is an additional rear light bar legal where I live?
Both product pages state that rules about additional rear lighting vary by state and country, and advise checking local requirements before installing. That is a genuine question to resolve in your own jurisdiction — the manufacturer cannot answer it, and the product being reversible does not make it permitted.
8. The Bottom Line
Two products, one decision, and the decision is aesthetic. If you want the rear of the car to read as a striped band when you brake, take the zebra. If you want movement — a pulse running across — take the heartbeat. There is no performance argument to make between them, because the spec sheets do not contain one.
The harder question comes first, though, and it is the one worth checking before anything else: whether your Model Y is a 2020–2024 car at all. Both bars stop there, and the Juniper exclusion is stated plainly on both pages precisely because it is not obvious from a photograph.
And whichever you choose, read the note about local lighting rules. It is the least exciting sentence on either page and the only one that can affect whether the upgrade is allowed to stay on the car.
Disclaimer: Fitment is limited to Model Y 2020–2024; Model Y Juniper 2025 and later is not supported. Rules on additional rear lighting vary by state and country — check your local requirements before installing. Professional installation is recommended. This product supplements the factory lighting and does not replace it.